Step-by-Step Guide: How to Deep Clean Your Bissell Crosswave Brush

The Bissell Crosswave is a popular cleaning machine that makes it easy to clean carpets, hard floors, and other surfaces. The machine is equipped with a brush roll that picks up dirt and debris while also scrubbing the surface clean. However, over time, the brush roll can become clogged with dirt and hair, which can affect its performance. To keep your Bissell Crosswave running at its best, it’s important to clean the brush roll regularly. In this guide, we’ll show you how to clean your Bissell Crosswave brush to ensure that it continues to operate efficiently and effectively.

Why do you need to deep clean your Bissell Crosswave brush?

Regular cleaning of your Bissell Crosswave Brush is essential to keep it in optimal condition. Without regular maintenance, the brush can become clogged with debris and reduce effectiveness, decreasing its lifespan. Dirty brushes also spread bacteria and dirt onto floors, making them even dirtier. Regular brushing will keep both surfaces sparkling clean.

A Step-by-Step Guide for Deep Cleaning Your Bissell Crosswave Brush

Step 1: Disconnect Your Brush Roll from Bissell Crosswave Machine: Before you can thoroughly clean your Bissell Crosswave Brush, you must first disconnect it from its main unit. Locate the brush roll at the bottom and push the release button to take it out. Set this aside, and then unplug your device completely.

Step 2: Take out the brush roll: To remove the brush roll from your Bissell Crosswave Brush, use either a screwdriver or wrench to carefully lift it out of the unit. Once out, set it aside to one side for safekeeping.

Step 3: Clean the brush roll: Use a soft-bristled toothbrush to gently scrape away hair and debris from the brush roll. To guarantee that it works properly, make sure all debris has been cleared away.

Step 4: Soak Your Brush Roll: Add a few drops of dish soap to warm water and soak the brush roll in it for about 10-15 minutes. This will loosen any dirt or debris stuck to the brush roll.

Step 5: Clean the brush roll: After the brush roll has been soaked, use a soft-bristled toothbrush to gently scrub it clean. Make sure you rub both sides of the brush roll for thorough removal of soap residue. Finally, rinse under running water to rinse away any soap residue left behind.

Step 6: Finish by drying the brush roll: After cleaning the brush roll, use a towel to dry it completely. Allow the brush roll to air dry completely before reassembling it.

Step 7: Empty the Brush Housing: Once the brush roll has soaked, you can use a soft-bristled toothbrush to thoroughly clean its housing. Make sure to get rid of any debris or dirt that might have settled inside the housing.

Step 8: Reassemble Your Bissell Crosswave Brush: After your brush roll has dried, you can reassemble your Bissell Crosswave Brush. Carefully insert it back into its housing by tightening screws on each side. Connect the brush roll to its main unit, and then plug in your Bissell crosswave.

How Often Should I Clean My Bissell Crosswave Toothbrush?

The Bissell Crosswave brush can clean both hard floors and carpets. Rotating at high speeds, it removes dirt and other particles. However, accumulated hair and dirt can reduce its effectiveness, cutting its life expectancy in half. To ensure optimal performance from this tool, regularly cleaning it is essential.

When it comes to deep cleaning your Bissell Crosswave toothbrush, the frequency of usage, surfaces you clean and how much dirt and debris accumulate on it are all factors to consider. As a rule of thumb, deep clean your brush at least once every four to six uses; if used less frequently then clean at least once each month.

If your pets shed hair or you clean a lot of soiled areas like the bathroom or kitchen, you may need to clean your brush more frequently. In such cases, inspect it frequently and clean it whenever debris appears.

To properly care for your Bissell Crosswave toothbrush, first remove it from its machine and disassemble it. Use a brush or comb to brush away any hairs stuck to the bristles before soaking the brush in warm water, vinegar or commercial cleaner for about 10-15 minutes. Rinse thoroughly after soaking and allow to air-dry completely.

Bissell Crosswave toothbrushes should be cleaned regularly to maximize their life expectancy and performance. Neglecting to clean your brush can cause clogs, reduced suction power, or even damage to the machine; so it’s essential that you follow manufacturer’s instructions and clean the brush frequently.

Can I clean the Bissell Crosswave toothbrush without taking it out of the machine?

Though it is possible to clean the Bissell Crosswave toothbrush without taking it out of the machine, doing so is not recommended. Although this might seem like a straightforward option, doing so can cause several issues which could negatively impact both durability and performance of the device.

Clogs on a brush can make it difficult to reach all bristles and collect any dirt or debris if not taken out of the machine. Not only that, but clogs may reduce suction power, making cleaning less efficient. Not only that, but dirt and other particles could get stuck inside of the machine which could cause long-term harm if not cleared away thoroughly.

The Bissell Crosswave toothbrush can be difficult to clean without taking out its bristles, leading to mold growth and other health complications that could prove disastrous in the long run.

Before cleaning your machine brush, it is recommended that you take it apart and reach all bristles. After disinfecting the brush, let it air dry completely before attaching it back onto your machine.

If it is inconvenient for you to take the brush out of the machine each time, there are other methods you can try. Avoid using the brush on heavily soiled areas; instead, use a separate tool to eliminate most dirt and debris. Doing this reduces dirt buildup on the brush itself, making cleaning much simpler and more effective.

Can I clean the Bissell Crosswave toothbrush with vinegar or bleach?

Bissell Crosswave toothbrushes can be cleaned with vinegar or bleach. However, be sure to use the correct concentration of cleaning agents for maximum protection on both the brush and machine.

Vinegar can be used to clean the Bissell Crosswave toothbrush. Simply mix equal amounts of warm water and white vinegar in a container, letting the solution sit for 10-15 minutes. After soaking, wash the brush with warm water and air dry completely before assembling and attaching it to your machine.

Bleach can effectively kill bacteria and germs on a Bissell Crosswave toothbrush if used properly. However, be careful as bleach has the potential for damaging the brush as well as being highly corrosive. To use bleach properly, follow the manufacturer’s instructions for diluting bleach and wearing gloves for protection against skin contact. Allow the solution to soak into the brush for 10-15 minutes, rinse it with clean water, then allow it to air-dry completely.

It is essential to remember that bleach or vinegar can damage the bristles of your Bissell Crosswave toothbrush. It is best to only use these on the brush itself and then follow up with mild detergent or soap.

Additionally, it’s essential to follow the manufacturer’s guidelines and instructions when cleaning a Bissell Crosswave toothbrush. Doing so will allow you to utilize appropriate cleaning agents and techniques without damaging the machine.

How should you dry the Bissell Crosswave toothbrush after cleaning it?

After cleaning your Bissell Crosswave toothbrush, it’s essential that you thoroughly dry it. Doing so prevents bacteria and mold growth that could lead to serious health issues or even damage to the machine itself. Here are some helpful tips for drying the brush properly:

To remove excess water from the brush, gently shake it.

Use a Towel: Gently rub the bristles of your brush with a dry towel to avoid damaging its bristles. Be gentle when applying this solution. Once all water has been removed with a towel, let the brush air dry completely. Place it in an area that stays dry for at least 24 hours. Hairdryers can expedite drying time. However, be sure to keep them at a distance of several inches from the brush in order to avoid damaging or overheating its bristles.

Dry It: Make sure the brush is completely dry before using it. Doing so will prevent moisture accumulation and cause bacteria or mold growth that could harm the machine.

These tips will help ensure your Bissell Crosswave brush remains clean and dry, thus extending its life expectancy and maintaining performance.

How long does it take to clean the Bissell Crosswave toothbrush?

Cleaning a Bissell Crosswave toothbrush can take up to 10 minutes depending on how much dirt and debris has built up. Depending on the method employed and tools utilized, this time frame for deep-cleaning the brush may range from 10-30 minutes.

Mix a cleaning solution with some water, then soak your brush in it for several minutes. This will allow the solution to penetrate dirt and loosen it. Next, scrub away any remaining grime with a sponge or brush before thoroughly rinsing with clean water before drying completely.

A brush cleaner or other cleaning tool can make the process faster and more efficient. These instruments are specifically designed to clean the bristles on a Bissell Crosswave toothbrush, as well as help remove dirt and other particles faster.

No matter the cleaning method you use, it is imperative to thoroughly clean your Bissell Crosswave toothbrush in order to eliminate dirt and debris. Doing so will extend the life of your machine and keep it running optimally; plus, ensure your floors are spotless!


Finally, deep cleaning your Bissell Crosswave brush is essential to maintain its performance and longevity. The process involves taking out hair, debris, and other particles stuck in its bristles which can cause it to lose suction and reduce cleaning effectiveness.

To thoroughly clean your Bissell Crosswave brush, you will need to take several simple steps: remove the roll of bristles, wash with warm water and soap, then use a comb or brush to scrape away any remaining debris. Moreover, you may wish to consider using an antibacterial solution on the brush in order to disinfect it and prevent bacteria growth.

By following these steps regularly, you can guarantee your Bissell Crosswave continues to perform optimally and gives your floors a deep clean every time you use it. So if you want your home looking and feeling clean and refreshed, don’t forget to give your brush some TLC too!


Hi, I'm Asim! I love giving you cleaning guides, tips and tricks that will make your place sparkle and shine. Through years of practice, I've learned effective ways to clean and can't wait to help you. From tough spots to general cleaning, I can help you. Come along with me on this cleaning adventure, where I'll give you tips and tricks to make your cleaning process easier. Let's work together to make clean haven.

Leave a Reply

Your email address will not be published. Required fields are marked *